Votes - 2, Average rating: 3 ( )

Manafacture: Pioneer File size: 17.78 mb File name: Language of manual:

Photos and specs  Pioneer  S-21W

Connecting the speakers To get the best out of your speakers it is important that you connect them properly to your receiver. Each speaker connection consists of a positive (+) and a negative (–) terminal. These should be matched between the receiver and the speaker. 1 Attach one end of the supplied speaker cord to the rear of the each speaker. • Connect the wire with the colored marker to the red (+) terminal; the plain wire to the black (–) terminal. Press down the spring-loaded tab and insert the wire, as shown below. Release the tab to secure the wire. Red (+) Black (–) Red colored marker 2 Connect the other end of each speaker cord to your receiver. • To connect, insert the colored wire into the matching positive (colored) terminal and the other wire into the negative (black) terminal. See also the Operating Instructions that came with your receiver. En EnglishEnglish • These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or disconnecting the speaker cords, disconnect the power cord before touching any uninsulated parts. • After connecting the plugs, pull lightly on the cords to make sure that the ends of the cords are securely connected to the terminals. Poor connections can create noise and interruptions in the sound. • If the cords’ wires happen to be pushed out of the terminals, allowing the wires to come into contact with each other, it places an excessive additional load on the receiver. This may cause the amp to stop functioning, and may even damage the receiver. • When using a set of speakers connected to an receiver, you won’t be able to obtain the normal stereo effect if the polarity (+, –) of one of the speakers (left or right) is reversed. Operation • Set the receiver’s cross-over frequency at 200 Hz. Wall-mounting the front and surround speaker system Attaching the brackets • When attaching the speakers to brackets, always use the furnished brackets for wall mounting. • Make sure to tighten the supplied screw as securely as possible when attaching the bracket to the back of the speaker. • Do not attach brackets to center speaker or subwoofer. • Use the M5 metric thread screw. Do not use inch thread screw. Before mounting • Remember that the speaker system is heavy and that its weight could cause the wood screws to work loose, or the wall material to fail to support it, resulting in the speaker falling. Make sure that the wall on which you intend to mount the speakers is strong enough to support them. Do not mount on plywood or soft surface walls. • Mounting screws are not supplied. Use screws suitable for the wall material and support the weight of the speaker. If you are unsure of the qualities and strength of the walls, consult a professional for advice. Screw (supplied) 5 mm (3/16 in.) to 7 mm (9/32 in.) Mounting screw (not supplied) 5 mm (3/16 in.) 10 mm (13/32 in.) En Specifications S-21W Power Amplifier Power Output (Peak) ................................................................................................. 160 W Power Amplifier Power Output (RMS) ....................................................... 100 W (100 Hz, 4 ., THD 10 %) Power Amplifier Power Output (FTC) .............................................. 80 W (35 Hz to 500 Hz, 4 ., THD 1 %) Input (sensitivity at 100 Hz) LINE LEVEL (RCA jack) ......................................................................... 300 mV Cabinet.......................................................................................................................... Bass-reflex, floor type Speaker ..................................................................................................................................16 cm cone type Speaker Frequency range .................................................................................................... 33 Hz to 700 Hz Power Requirements European model........................................................................................ AC 220 V to 240 V, 50 Hz/60 Hz U.S., Canadian model ....................................................................................................... AC 120 V, 60 Hz Other model ..............................................................................................AC 110 V to 240 V, 50 Hz/60 HZ Power Consumption ................................................................................................................................ 25 W Power consumption in standby ................................................................................................. 0.5W or less Outline Dimension....................................................................... 230 mm (W) x 408 mm (H) x 344 mm (D) (9 1/16 in.(W) x 16 1/16 in.(H) x 13 17/32 in. in.(D)) Weight (without package) .................................................................................................. 6.5 kg (14 lb 5 oz) S-11 Front speakers / Surround speakers Enclosure Front speakers ..........

Download now

Please, enter two numbers from picture: