Votes - 4, Average rating: 3.5
(
)
)
|
Other manuals for this model:
manual abstract
2 In the sender system, enter the Settings menu and select [Move track data]. 3 Read the contents in [Read me], and then select [Next]. 4 Select the direction for the track data from the [Moving direction] pull-down menu, and then select [Check]. 5 Repeat steps 2 to 4 in the receiver system. If all of the data cannot be moved for some reason (for example, because of insufficient HDD space or limits on the number of folders in the receiver system), a message will appear. To cancel moving, select [Close], and then select [Stop] in step 6. The unit automatically restarts after cancelling. 6 When the data moving display appears, select [Start]. 7 Select [Yes]. The moving starts. When the moving has completed, the unit automatically restarts, and then turns off. 110GB Troubleshooting Troubleshooting If a problem occurs while operating the unit, follow the steps described below before consulting the nearest Sony dealer. If an error message appears, it is recommended that you make a note of its contents for reference. 1 Check to see if the problem is listed in this “Troubleshooting” section. For details about troubleshooting the Instant (S-IWS) connection, refer to the “Quick Connection and Setup Guide” supplied with the NAS-SC55PKE. 2 Check the customer support site of Sony Europe at com/ (for customers in Europe only). You will find the latest support information and a FAQ at this web site. 3 If after steps 1 and 2 you still cannot solve the problem, consult your nearest Sony dealer. If the problem persists after doing all of the above, consult your nearest Sony dealer. How to reset the unit It is usually unnecessary to reset this unit. However, on rare occasions, the unit enters an abnormal state and stops responding to button or on-screen operations. In this case, reset the unit by pressing the . button together with the ./. (power) button on the unit. Power The unit does not turn on. . Connect the power cord to the wall outlet firmly. . Disconnect the power cord from the wall outlet. After about a minute, reconnect the power cord and press the ... (power) button to turn on the unit. The messages “Starting up”, “Please wait.”, “Turning-off after setting is applied.” appear in the display and the unit automatically turns off. . This is not a problem. After the power cord is connected, the unit automatically makes the initial settings and enters standby mode. The unit turns on when you press the ... (power) button. It takes a while for the unit to turn off while the messages “Starting up”, “Please wait.”, “Turning-off after setting is applied.” are displayed. . If the unit’s HDD has a large amount of recorded data, it will take a while before the unit turns off. It takes a while for the unit to turn on as the messages “Starting up” and “Please wait.” are displayed. . If you use the unit in an environment without a broadband router, it takes about 30 seconds for the unit to obtain an IP address and then to turn on. . The IP address set for the unit is already being used by another device. Set a different IP address. 111GB The unit does not turn off. . The ... (power) button may not respond while the unit is making the initial settings or is still starting up. . The On/Standby indicator lights up orange and the illumination panel flashes slowly while the unit is analyzing the recorded materials. If you want to cancel the analysis and turn off the unit, press the . button. . As long as the unit is active as a server and the client device is playing audio data, the server function remains active and the power stays on even if you press the ... button to turn the unit off (the display turns off and the illumination panel slowly flashes). Press . to cancel the server function and turn off the unit. . If you disconnect the power cord from the wall outlet while the On/Standby indicator is lit up red, the indicator may remain lit for a little while longer. There is noise from the unit or the unit remains warm after the power is turned off. . When standby mode is set to “Quick start- up”, some parts of the internal system remain active and the internal fan sometime activates. Display The display on the screen is distorted. . The unit is being subjected to shocks or vibrations. Place the unit at a stable location. . On rare occasions, characteristics of the HDD may cause some distortion in the display; this, however, is not a malfunction. Sound output There is no sound. . Press the VOLUME +/– buttons or the MUTING button to cancel muting. Sound monitoring cannot be done while Recording Timer is in progress. . Cancel pause. . Confirm that nothing is connected to the PHONES (headphones) jack. . Check the connections of the external component. . Connect the speaker cords firmly. The right-left sound balance is bad or reversed. . Connect the speakers and other devices correctly. The sound has no depth and seems to be monaural. . Connect the speakers and other devices correctly. There is severe hummi...