Votes - 2, Average rating: 3
(
)
)
|
manual abstract
10 Making Connections 10 Making Connections LSF-1010 (EN) Before Connecting... You can connect the subwoofer in any of three ways, as described below. Refer to the indicated page for connection 1. If your amp or receiver includes jack: For connection instructions, see page 11, “Connecting to Amp’s SUBWOOFER PRE-OUT Jack.” 2. If your amp or receiver does not include PRE-OUT jack: In this case, you can connect to the speaker output terminals receiver. For instructions, see page 12, "Connecting to Amp's Speaker Output Terminals." 3. If your amp or receiver includes standard PRE-OUT It is also possible to connect to standard PRE-OUT jacks on your amp or receiver. For instructions, see page 13, "Connecting to Amp's Standard PREOUT Jacks." • It is also possible to connect the subwoofer’s LINE IN jacks to the REC OUT or LINE OUT jacks on the amp or receiver. If you make this type of connection, however, volume adjustments at the amp side will not affect the volume from the subwoofer. Again, see page 13, “Connecting to Amp’s Standard PRE-OUT Jacks.” Subwoofer To electrical outlet (wall outlet) 1LINE IN jacks Connect to the SUBWOOFER PRE-OUT output or other line-level output on your amplifier or receiver. 2FROM AMPLIFIER terminals Connect to the speaker output terminals on your amplifier or receiver. 3TO SPEAKER terminals These terminals output the signal received at the FRONT AMPLIFIER terminals. You can use them to relay the signal to your front speakers. CAUTION Do not plug in the power cord until you have finished making all connections. NoteNote 1. Be sure to connect all cables securely. Insecure connections may result in distortion or noise. 2. Always unplug the power cord before connecting or disconnecting cables. Leaving the power plugged in while making connections may result in malfunction or damage. 3. Never short the (+) and (–) speaker wires together. 4. Do not reverse L and R or (+) and (–) sides when making connections. Reversal of sides or polarities may result in unnatural, incorrectly positioned sound. 5. Please read the documentation that came with the devices you are connecting to, and make connections accordingly. 11Making Connections 11Making Connections LSF-1010 (EN) Connecting to Amp's SUBWOOFER PRE-OUT Jack Using the pin-plug audio connect the SUBWOOFER PRE-(MONO) LINE IN jack on the subwoofer. Pin-plug audio cable (included) CAUTION Do not plug in the power cord until all connections. White stripe SPEAKERS SUPER WOOFER PRE OUT LR a » a » SUBWOOFER PRE-OUT jack (on amp or receiver) Satellite speaker (right) Speaker cord (included) Included speaker cord Subwoofer Satellite speaker (left) 12 Making Connections 12 Making Connections LSF-1010 (EN) Connecting to Amp's Speaker Output Terminals Connect the FROM AMPLIFIER speaker output terminals on Connect the TO SPEAKERS terminals all connections using speaker CAUTION Do not plug in the power cord until all connections. Speaker cord for the connection between purchase this cord separately. IMPORTANT The satellite speakers have a nominal impedance of 6 ohms. Be sure that your amplifier or receiver is able to work with 6-ohm speakers. SPEAKERS LR » a» a 1324a »a » Speaker cord (purchased separately) Subwoofer Speaker output terminals (on amp or receiver) Speaker cord (included) Satellite speakers (right) (left) Included speaker cord White stripe Twist the wire. NoteNote If your amplifier or receiver has two sets of speaker output terminals, you can connect the front speakers directly to the second set of terminals (rather than connecting them to the TO SPEAKER terminals on the subwoofer). 13Making Connections 13Making Connections LSF-1010 (EN) Connecting to Amp's Standard PRE-OUT Jacks Connect the PRE-OUT on the subwoofer. Make the connection using pin-(The cable is not included CAUTION Do not plug in the power cord until ing all connections. NotesNotesNotes • It is also possible to connect the subwoofer's LINE IN jacks to the REC OUT or LINE OUT jacks on the amp or receiver (using the same cable as described here). If you make this type of connection, however, volume adjustments at the amp side will not affect the volume from the subwoofer. This means that you will need to manually adjust the subwoofer volume each time you adjust the volume at the amp side. • If you wish to connect the subwoofer to the PRE-OUT jacks on a standalone preamplifier, the preamp unit must include a second set of terminals for connection to speaker amps, and must be capable of simultaneous output to both the PRE-OUT jacks and the speaker-amp jacks. a»a» SPEAKERS L R LR PRE OUT a »a » Pin-plug audio cable (purchased separately) PRE-OUT jacks (on amp or receiver) Subwoofer Satellite speakers (right) (left) Included speaker cord White stripe Note About Pin-Plug Cables Some commercially available pin-plug cables have relatively plug ends that may become bent if the subwoofer is installed vertically. Bending of plugs may cause internal wires to break, resulting in loss of soun...