Votes - 3, Average rating: 4.7
(
)
)
|
Photos and specs Yamaha NS-50F |
manual abstract
• Any time you note distortion, reduce the volume of your amplifier immediately. Make sure the input power does not exceed the specified maximum input power, otherwise the speakers will be damaged. • Do not attempt to clean the speakers with chemical solvents as this might damage the finish. Use a clean, dry cloth. • Do not attempt to modify or fix the speakers. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. Note: This speaker is magnetically shielded, but placing them too close to a TV may impair the TV picture. If this happens, move the speaker away from the TV. DeutschFrancais EspanolEnglish E-1 Precautions When Positioning the Speakers Precautions When Positioning the Speakers ¦ For safe and proper use of the speaker: • Position the speaker in a location that is solid, level, smooth, and low (with respect to the floor). • Do not push or apply pressure to the side of the speaker when moving, or lean objects against the side of the speaker. • Do not sit on or set objects on top of the speaker. Vibrations or jolts associated with earthquakes and other phenomena or activities may cause the speaker to fall over. For safety reasons, using commercially available products that increase stability in the speaker is recommended (metal fittings or chains, etc.). ¦ Use the stands included with the speaker to increase stability: Be sure to use the stands regardless of where the speaker is positioned. Attaching the stands included with the speaker reinforces the base of the speaker not to fall over. Please be cautioned that even though the stands are connected, this does not guarantee that the speaker will not fall over. Supplied Accessories • Speaker cable (4 m) . 1 •Stand . 4 •Screw . 8 •Pad . 4 Placing the Speakers Place the speakers on a sturdy, vibration-free surface. ¦ Using as Normal Stereo Speakers To get the best stereo performance, angle the speakers inward so as to create a triangle, with the listener at the apex. ¦ Using as Front Speakers in a Surround Sound System Position the speakers both side of your TV. The positioning of these speakers is important because they provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equidistant from the TV. Surround L Center Surround R NS-50F Subwoofer Attaching the Stands When placing the speakers, be sure to use the stands to increase stability. Use the 8 specified holes located on the base of the speaker. ¦ Procedure: 1. Put the screw through the inner hole of the stand, and screw it into the outside hole of the speaker. Do not tighten too much at this point. Outer hole Inner hole 2. Put a screw through the outer hole on the stand, and screw it into the other hole on the base of the speaker. 3. Tighten both of the screws firmly. 4. Attach a pad to the bottom of the end portion of the stand. 5. Attach the other stands to the other corners of the base of the speaker in the same way and confirm that all 4 stands have been firmly attached. 4 1 2 English Note: Be careful not to apply force to the side of the speaker, otherwise the speaker may fall causing damage to the speaker or personal injury. E-3 Always turn off your amplifier or receiver before making any connections. ¦ Preparing Your Speaker Cables Carefully remove 10 mm (3/8 ”) of insulation from both ends of your speaker cables and twist the bare wires tightly, as shown. 10 mm (3/8 ”) Good No Good ¦ Hookup SPEAKERS A B LR ++ – – + – Loosen Tighten Amplifier or receiver Notes: • Make sure that the bare wires are not touching each other as this could damage the speaker and amplifier. • Connect one speaker to the left terminals of your amplifier, and another speaker to the right terminals, making sure not to reverse the polarity (+, –). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass. ¦ Using a Banana Plug 1 32Banana Plug 1. Remove the speaker terminal cover by gently pulling it toward you. 2. Tighten the terminal knob. 3. Simply insert the banana plug into the terminal. Removing the front cover Removing the front cover Note: When removing the cover, be careful that you don’t touch the drive units, and don’t exert excessive force with any tools. Specifications Type................2-way bass-reflex speaker system magnetic shielding type Drivers...........................3 cm (1 ”) dome tweeter 16 cm (6.5 ”) cone woofer x2 Impedance ......................................................6 . Frequency response .......................35 Hz–35 kHz Rated Input power ....................................... 80 W Maximum input power .............................. 240 W Sensitivity...................................90 dB/2.83 V/m Crossover frequency................................... 2 kHz Dimensions (with the stand) (W . H . D) .... 233 (9.2 ”) . 880 (34.6 ”) . 271 (10.6 ”) mm Weight ......................................12.5 kg (27.6 lbs) * Speci...