Votes - 3, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
Thank you for selecting this YAMAHA NS-300/NS-200 speaker system. S Read these precautions carefully before using your speaker. . Any time you note distortion, reduce the volume control on your amplifier to a lower setting. Never allow your amplifier to be driven into “clipping”. Otherwise the speaker may be damaged. . When using an amplifier with a rated output power higher than the nominal input power of the speaker, care should be taken never to exceed the speaker’s maximum input. . Do not attempt to clean the speaker with chemical solvents as this might damage the finish. To clean, wipe with a dry, soft cloth. . To prevent the enclosure from warping or discoloring, do not place the speaker where it will be exposed to direct sunlight or excessive humidity. . Do not place the speaker where it is liable to be knocked over or struck by falling objects. Stable placement will also ensure better sound performance. . Secure placement or installation is the owner’s responsibility. YAMAHA shall not be liable for any accident caused by improper placement or installation of the speaker. PRECAUTIONS WHEN POSITIONING THE SPEAKERS The speaker is constructed with the majority of the weight located in its upper portion, and is thus susceptible to falling over if proper care is not taken to insure its stability. If the speaker falls over, it may damage the speaker or be the cause of injury (or even death) to persons and/or damage to personal property. For safe and proper use of the speaker: • Position the speaker in a location that is solid, level, smooth, and low (with respect to the floor). • Do not push or apply pressure to the side of the speaker when moving, or lean objects against the side of the speaker. • Do not sit on or set objects on top of the speaker. Vibrations or jolts associated with earthquakes and other phenomena or activities may cause the speaker to fall over. For safety reasons, using commercially available products that increase stability in the speaker is recommended (metal fittings or chains, etc.). Use the stands included with the speakers to increase stability: . Stands Be sure to use the stands regardless of where the speakers are positioned. Attaching the stands included with the speakers reinforces the base of the speaker not to fall over. Please be cautioned that even though the stands are connected, this does not guarantee that the speakers will not fall over. HOW TO USE THE ACCESSORIES INCLUDED WITH THE SPEAKERS n Attaching the stand n Attaching the spike English Stand x 4 Screw (6 mm) x 4 Wood screw (4 mm) x 4 Washer x 4 Pad x 4 When positioning the speakers, be sure to use the stand to increase stability. Use the 8 specified holes located on the base of the speaker. Procedure: . Put the 6 mm screw through the inside hole on the stand. . Place a washer on the screw on the speaker side of the stand and attach to the speaker at one of the outside holes on the base of the speaker. At this time, attach the stand so that it can still be moved slightly. . Put the 4 mm wood screw through the outside hole on the stand, and screw into the inside hole on the base of the speaker. . When both screws have been attached, tighten both of the screws so that the stand is firmly in place. Be sure to check that the stand is firmly attached. A Attach the pads to the bottom of the end portion of the stand. A Attach the other stands in the same manner and confirm that all 4 stands have been firmly attached. . Place the speaker in the desired location. Note If force is applied to the side of the speaker, it may fall and damage the speaker or cause personal injury. Please be careful. Spike x 4 When setting up the speakers on a thick carpet, use the spikes instead of the stand. With 4 points set in place to achieve increased stability and improvements in sound quality. Procedure: . Set the nut close to the tip of the spike and screw them into the bottom of the speaker at each of the four specified holes. . Place the speaker in the desired location in an upright position and adjust the length of the spike to match the depth of the carpet. . When adjustment is complete, twist the nut up to the base of the speaker firmly. Notes . The tips of the spikes may scratch or otherwise damage the flooring. Please be careful when positioning the speakers. . If force is applied to the side of the speaker, it may fall and damage the speaker or cause personal injury. Please be careful. CONNECTIONS TO YOUR AMPLIFIER CONNECTIONS TO YOUR AMPLIFIER e that the amplifier is switched off.
Speakers & Subwoofers - NS-200 (72.39 kb)