Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Set the nut close to the tip of the spike and screw them into the bottom of the speaker at each of the four specified holes. . Place the speaker in the desired location in an upright position and adjust the length of the spike to match the depth of the carpet. . When adjustment is complete, twist the nut up to the base of the speaker firmly. Notes . The tips of the spikes may scratch or otherwise damage the flooring. Please be careful when positioning the speakers. . If force is applied to the side of the speaker, it may fall and damage the speaker or cause personal injury. Please be careful. CONNECTIONS TO YOUR AMPLIFIER Before making connections, make sure that the amplifier is switched off. SPEAKERS A B LR ++ – – Speakers output terminals of the amplifier – Amplifier or Receiver + Speaker (L) Speaker (R) Red (+) Loosen Tighten Black (–) n Connections . Connect the screw-type input terminals at the rear of the speakers to the speaker output terminals of your amplifier with the speaker cables. . Connect the (+) terminals on both the amplifier and the speakers using one side of the cable. Connect the (–) terminals on both components using the other side of the cable. . Connect one speaker to the left (marked L) terminals of your amplifier, and another speaker to the right (marked R) terminals, making sure not to reverse the polarity (+, –). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass. Procedure: A Loosen the terminal knob. A Remove approx. 10 mm insulation from the speaker cable and insert the bare wire end properly into the terminal hole. A Tighten the knob. A Test the security of the connection by tugging lightly on the cable at the terminal. Note Do not let the bare speaker wires touch each other as this could damage the speaker and/or the amplifier. PLACING THE SPEAKERS n Using as 2ch stereo speakers Better stereo images will be obtained when the speakers are slightly angled in towards the listeners. n Using as main speakers in a multi channel system Position the speakers on both sides of the TV. The positioning of speakers is important, because it controls the whole sound quality of a multi channel system. Set up the speakers on the basis of your listening position by following the owner’s manual supplied with your amplifier. Rear Speakers SubwooferCenter NS-120 NS-120 Front Effect Speakers REMOVING THE FRONT COVER The front cover is fastened to the enclosure at six points, and can be removed if desired. To remove the cover, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the six pegs on the inside surface of the cover with the six corresponding holes on the speaker and push gently. Note When the cover is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools. SPECIFICATION Type ..................................... 2-way bass reflex speaker system (Magnetically-shielded type) Driver........................................................... 13 cm cone woofer 3 cm dome tweeter Nominal Impedance .......................................................6 ohms Frequency Response ........................................ 42 Hz – 35 kHz Nominal Input Power ......................................................... 60 W Maximum Input Power .................................................... 200 W Sensitivity .......................................................... 88 dB/2.83 V/m Crossover Frequency ....................................................... 3 kHz Dimensions (W x H x D) ............................ 168 x 800 x 269 mm Weight ............................................................................12.5 kg Accessories ................................................................ Stand x 4 Screw (6 mm) x 4 Wood screw (4 mm) x 4 Pad x 4 Spike x 4 Nut x 4 . Specifications subject to change without notice due to product improvements. . Care should be taken not to exceed the input power values noted above. English Merci pour avoir choisi le systeme d’enceintes YAMAHA NS-120. PRECAUTIONS Lisez ces precautions attentivement avant d’utiliser vos enceintes. . Si vous notez une distorsion du son, reduisez le reglage du volume sur votre amplificateur. Ne laissez jamais votre amplificateur en position “d’ecretage”. Sinon, les enceintes risqueraient d’etre endommagees. . Lors de l’utilisation d’un amplificateur avec une puissance de sortie plus elevee que la puissance nominale d’entree des enceintes, faites attention de ne jamais depasser le niveau d’entree maximum des enceintes. . N’essayez pas de nettoyer les enceintes avec des solvants chimiques car cela risquerait d’endommager la finition. Pour les nettoyer, utilisez un chiffon doux et sec. . Pour eviter que le coffret ne se deforme ou se decolore, ne placez pas les enceintes en plein soleil ou dans un endroit tres humide. . Ne placez pas les enceintes dans un endroit ou elles risquent d’etre renversees et ou des...