Votes - 2, Average rating: 5 ( )

Manafacture: Altec Lansing File size: 120.84 kb File name: 4b033fd4-b250-4f0c-a01f-e76ab417f3b3.pdf Language of manual:

IMPORTANT – This warranty does not cover: • Damage that is the result of misuse, abuse, accident (including but not limited to damage by water), faulty hookup, defective or maladjusted associated equipment, or the use of the Product with equipment of which it was not intended. • Cosmetic defects that appear more than thirty (3) days after the date of purchase. Cosmetic damage caused by improper handling is also excluded. • Products that are used for commercial purposes. • The cost of removing or reinstalling the Product. • Damage that occurs while the Product is being shipped to whoever will service it. See the information above regarding shipping procedures. This warranty is void if: • The Product identification or serial number is removed or defaced in any way. • The Product is serviced or repaired by anyone other than a/d/s/ or an authorized a/d/s/ dealer or service agency. Original sales receipt: • Be sure the retail dealer has written on it the date, model number and serial number (if applicable) of the Product. This information is required for warranty service. This warranty is limited to: • Products purchased from authorized a/d/s/ retail dealers in the United States. a/d/s/ will supply a list of authorized dealers on request. In order to obtain warranty service you must: • Return the Product, freight prepaid, to the a/d/s/ dealer from which it was purchased, an Authorized a/d/s/ independent service agency, or to a/d/s/., If necessary you may call a/d/s/ Customer S e rvice Department for the names and address of authorized independent service agencies in your are a . • Provide proof of purchase in the form of a copy of your original sales receipt. The date, model number and serial number (if applicable) of the Product must be written on the sales receipt. audio adjustments unpacking Adjust the gain of the subwoofer amplifier to blend in with the midrange and high frequency speakers. These subwoofers are heavy. Rather than lifting the unit out of the shipping carton, turn the open Ideally the amplifier powering the ie subwoofer has an electronic crossover, If it does adjust it for the carton over, and lift it off the subwoofer. Then remove the packing corners from the subwoofer and best sound quality, the crossover setting should be between 50-100 Hz. If the amplifier does not have then remove it from the plastic bag. an electronic crossover, a 5 mH coil in series with the enclosure is acceptable. If the system is lacking mid-bass response reverse the speaker wires to the ie subwoofer and listen again. If the mid-bass response improves leave it alone, if not return the wires to the original position. placement 1. First turn factory radio to 3/4 volume. Unlike high frequency sound, our ears have difficulty locating the source of deep bass sounds. 2. Turn up/down gain to blend with mid and high speakers. 3. Adjust crossover of amplifier for best sound. 4. Repeat steps 2 and 3 until desired sound is achieved. Consequently, you have a fair amount of flexibility in where you place the subwoofer in your vehicle. Typically the subwoofer is mounted in rear of the vehicle, either in the trunk, hatchback, or rear cargo area. For proper performance the port must not be closer than 3" from any walls, this will cause the performance to suffer. The enclosure can stand up or lie it on its side. mounting locations Brackets are supplied for mounting the enclosure either vertically or horizontally. Remove the proper screws from the enclosure and replace the screws through the bracket and then into the enclosure. Repeat for the other side. Screw the enclosure into the floor of the vehicle being careful to note where brake and fuel lines run on the other side. Do not mount the enclosure directly against a hard surface with out first putting down a piece of felt or cloth to prevent buzzes and rattles. Check to make sure that the enclosure screws are tightened properly, failure to do so may cause unwanted air leaks. Check to make sure that the screws mounting the enclosure to the floor are secure and tight. warnings and tips Always disconnect the battery ground wire before doing any work on your vehicle. Reconnect the cable only after the installation is complete and the wiring has been checked to make sure that there are no problems. If your radio features a code type security system, be sure you know the code before disconnecting the battery! system configurations The ie series subwoofers are designed to integrate with a wide variety of full range speakers. A typical installation consists of a factory stereo system driving an external amplifier powering the ie series subwoofer. A more advanced system utilizes separate midrange and hi frequency speakers and multichannel amplification, such as an a/d/s/ PH30 amplifier powering 346is speakers front and rear along with an ie series subwoofer. factory upgrade advanced system speaker connections The ie series subwoofers have a terminal cup mounted on one end of the speaker enc...

Download now

Please, enter two numbers from picture: