Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Always use electronic igniter for lighting each burner. 8. Refer to owner’s manual for match lighting procedure. 9. For assistance, call 1-800-527-0717. 10. To turn off, turn control knobs clockwise until it locks in OFF position. GRILL LIGHTING INSTRUCTIONS: FOR OUTDOOR USE ONLY Step 5 Attach the grease tray bracket onto the back cart panel by inserting the three tabs into the slots on the back cart panel. Note: When performing Step 6, lift grill body from front and rear panels to avoid injury to hands and fingers. Step 6 With the help of a friend, place grill body assembly on grill cart. Grill body will rest on upper side sections of cart. Align bolt holes located on the outside of the grill body assembly. Secure using four M6 X12mm bolts. At this point, fully tighten four bolts holding back panel from Step 4. Note: To install battery, unscrew igniter button cap. Insert battery with positive end towards button. Replace igniter button cap. Step 7 Install door bracket using four M6 X 12mm bolts. Make sure door stop is set toward back of cart. Step 8 Insert right side door over lower pivot (on bottom cart panel) then align door with cart frame. Depress spring pin located on top edge of door and slide door toward side cart panel until spring pin locks into hole in door bracket. Repeat for other door. Door bracket Spring Pin Lower Pivot Screw Holes Step 9 Attach side burner assembly to grill body assembly by inserting four M6 X 20mm bolts halfway into the screw holes of the grill body assembly. Then slide side burner assembly onto bolts and secure all four bolts. Install side burner grate and control knob. MAXIMUM SIDE BURNER LOAD = 15 lbs. 1. Read and follow all warnings and instructions in owner’s manual before lighting. 2. Open lid before lighting side burner. 3. Make sure all control knobs are in the OFF position. 4. Push and turn side burner control knob of that burner to HIGH. 5. Press the electronic igniter and hold for 3-5 seconds locks in OFF position. to light burner. 6. If burner does NOT ignite immediately, turn control knob to OFF, wait 5 minutes to allow gas to dissipate and repeat lighting procedure. 7. Refer to owner’s manual for match lighting procedure. 8. For assistance, call 1-800-527-0717. 9. To turn off, turn control knob clockwise until it SIDE BURNER LIGHTING INSTRUCTIONS: Side burner grate Step 10 Remove the plastic cap on gas supply manifold and attach rubber gas hose to gas supply manifold. Hand tighten first, then use supplied wrench to turn brass nut an additional 1/8 turn. Important: Do not overtighten. This could damage brass fitting. Warning: Never use your grill without leak testing all gas connections and hoses. See the section on “Leak Testing” in this manual for proper procedures. (See page 7) Step 11 Attach side burner igniter lead to the electrode as illustrated. Gas Hose ElectrodeBrass Nut Side Burner IgniterLead Step 12 Attach side table assembly to grill body assembly by inserting four M6 X 20mm bolts halfway into the screw holes of the grill body assembly. Then slide side table assembly onto bolts and secure all four bolts. Side Table Screw Holes Step 13 Insert grill bottom into opening on backside of grill. Make sure to slide tray onto tracks as illustrated. Grill Bottom Grease Tray Step 14 Slide grease tray into grease tray bracket located under grill bottom on backside of grill. Step 15 Place the porcelain coated heat shields on lower level of grill body assembly directly above burners. Step 16 Place porcelain cast iron cooking grills on support ribs directly above porcelain heat shields. Step 17 Place warming rack in slots above cast iron cooking grills. 1. Read and follow all warnings and instructions in owner’s manual before lighting. 2. Open lid before lighting burner. 3. Make sure all control knobs are in the OFF position. 4. Select the burner to be lit. Push and turn the control knob of that burner to HIGH. 5. Press the electronic igniter and hold for 3-5 seconds to light burner. 6. If burner does NOT ignite immediately, turn control knob to OFF, wait 5 minutes to allow gas to dissipate and repeat lighting procedure. 7. Repeat Steps 4-6 for lighting each burner. Always use electronic igniter for lighting each burner. 8. Refer to owner’s manual for match lighting procedure. 9. For assistance, call 1-800-527-0717. 10. To turn off, turn control knobs clockwise until it locks in OFF position. GRILL LIGHTING INSTRUCTIONS: FOR OUTDOOR USE ONLY Cooking Grills Porcelain Heat Shields Warming Rack Pro Series 2500 (Assembled) MAXIMUM SIDE BURNER LOAD = 15 lbs. ’ . . , , . ’ GRILL LIGHTING INSTRUCTIONS: ’ . . 6. If burner does NOT ignite immediately, turn control knob to OFF, wait 5 minutes to allow gas to dissipate and repeat lighting procedure. 7. Refer to owner’s manual for match lighting procedure. 8. For assistance, call 1-800-527-0717. 9. To turn off, turn control knob clockwise until it locks in OFF position. FOR OUTDOOR USE ONLY ACCESSORIES RIB RACK PROFESSIONAL S...