|
manual abstract
Lighting the Grill Using the Integra- Spark Ignition System · Open Lid or Hood (depending on the model) before lighting the grill to prevent an explosion from gas build-up. · The Lid (KangaTM series only) must never cover the cooking surface while the LP gas grill is in use or hot. · Always inspect the gas hose and regulator assembly before each use. If the hose is cut, damaged, or shows signs of excessive abrasion or wear, do not use the LP gas grill. Contact the manufacturer, as the hose and regulator assembly must be replaced with an assembly specified by the manufacturer prior to further use of the LP gas grill. How to light your LP gas grill (See diagram below for illustrations) 1) Open Lid or Hood (depending on the model) 2) Important: Make sure control knobs are turned “off” first. Open the LP gas cylinder valve by turning the valve handle counter-clockwise until it stops. 2. Turn LP cylinder handle counter-clockwise - “ON” 3) From the “Off” position, push control knob in on the left burner and turn counter-clockwise until you feel resistance. Pause 4 seconds, then continue turning the control knob until a click is heard and the burner is lit. 4) Light the remaining burners by turning the control knob counter-clockwise. Your grill has a crossover ignition system that allows the burners to light successively off one another. Confirm each burner is lit before lighting another burner. 5) If any of the burners do not light, repeat Step 3. The burner should light within three or four attempts. If burner still does not light, try the next burners from left to right. WARNING: If any or all burners fail to light after following Steps 3 & 4, turn all knobs to the “off” position and close the valve on the LP gas cylinder. Wait five minutes; then repeat all of the above lighting procedures. Note:If the burners still fail to light, refer to the Troubleshooting page. The burner can be lit manually, see Manual Lighting of the Grill. 6) After ignition, preheat the grill by turning the control to “High” position for 3-5 minutes. The grill should be pre-heated before every cooking session. The hood (Bonza™ series only) should be closed during preheating. The lid (Kanga™ series only) must never cover the cooking surface while the grill is in use or ishot. WARNING: If a burner goes out during the cooking cycle, turn all knobs to the off position and close the valve on the LP cylinder. Open hood (Bonza™ series only) and wait five minutes before attempting to relight the grill. 1. Open lid or hood (depending on model) 3. Push in and turn control knob counter-clockwise until you feel resistance, wait 4 seconds then continue until a click is heard and the burner is lit. 28 Manual Lighting of the Grill · Open Lid or Hood (depending on the model) before lighting the grill to prevent an explosion from gas build-up. · The Lid (Kanga™ series only) must never be covering the cooking surface while the LP gas grill is in use or hot. · Always inspect the gas hose and regulator assembly before each use. If the hose is cut, damaged, or showing signs of excessive abrasion or wear, do not use the LP gas grill. Contact the manufacturer, as the hose must be replaced with an assembly specified by the manufacturer prior to further use of the LP gas grill. How to manually light your LP gas grill 1) Open Lid or Hood (depending on the model) 2) Important: The LP gas cylinder valve must be opened first before turning the control knobs on the grill. Turn the handle on the LP cylinder valve counterclockwise until it stops. 3) Insert a lit match through one of the match-lighting holes underneath the front control panel on the grill. (See figure below). 4) Locate the control knob that corresponds to the match lighting hole that you are using. Push in and turn the control knob counter-clockwise until a click is heard. WARNING: If the burner fails to ignite after following the above procedure, turn all the knobs to the off position and close the valve on the LP cylinder. Wait five minutes and repeat all of the above manual lighting procedures. If the grill still fails to light, see the Troubleshooting page. 5) Light the remaining burners from left to right by turning the control knob counter-clockwise. Your grill has a crossover ignition system that allows the burners to light successively off one another. Confirm each burner is lit before lighting another burner. 6) After ignition, burners should be burned at the high position for 3-5 minutes in order to preheat the grill. This process should be done before every cooking session. The hood (Bonza™ series only) should be closed during preheating. The lid (Kanga™ series only) must never be covering the cooking surface while the grill is in use or hot. WARNING: If a burner goes out during the cooking cycle, turn all knobs to the off position and close the valve on the LP cylinder. Open hood (BonzaTM series only) and wait five minutes before attempting to relight the grill. 4. Push in and turn control k...
Other models in this manual:Convection Ovens - Bonza (661.7 kb)
Convection Ovens - Kanga (661.7 kb)