Login:
Votes - 5, Average rating: 4 ( )

User manual Coleman, model 9995A

Manafacture: Coleman
File size: 2.28 mb
File name: a6d2ecd0-05bd-40f1-9444-fbb7f2be339d.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


4. If you are unable to stop a leak, shut off the gas supply at the cylinder valve. Remove the cylinder from the grill. Call a gas appliance serviceman or L.P. gas dealer. DO NOT use grill until the leak is corrected. When to test for leaks: 1. Perform a leak test each time the gas supply cylinder is connected to the regulator. Leak test anytime a part of the gas system is replaced. 2. Perform a leak test at least once each year whether the L.P. gas supply cylinder has been disconnected or not. 3. Have a dealer check the cylinder for deterioration after 12 years, according to DOT regulations. Immediately replace cylinder if any deterioration is found CAUTION Inspect the gas supply hoses before each use. If there are cuts, damage, excessive abrasion or wear, replace the hoses prior to operating the appliance. During assembly of grill and when attaching or replacing the L. P. gas cylinder, insure that all gas supply hoses are free of kinks and/or damage and are at least 3" away from hot surfaces such as the grill housing. Use only hose replacements specified in the parts list. Start-Up Check List WARNING Failure to follow these safety steps before using grill each time could result in a fire that could be hazardous to you, your appliance or property. It is especially important to observe these steps after the grill has been stored, moved or cleaned. 1. Inspect the gas supply hoses before each use. Hoses can be burned or chafed if they are routed improperly. See that hoses have no kinks, sharp bends or tension. Insure that hoses are at least 3 inches away from any hot surface. If it is evident that there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the grill being put into operation. 2. Use only the gas specified. 3. Keep the grill on a level surface and lock the castors. 4. Keep grease pans empty at start up. 5. Do not use charcoal or lighting fluid. Lighting the Grill WARNING THE FOLLOWING RULES MUST ALWAYS BE FOLLOWED IN THIS ORDER : 1. Check that the Burner Control Knobs are turned to “OFF.” 2. Turn on fuel supply. For an L.P. gas cylinder, turn the top cylinder valve knob counterclockwise to open. 3. DO NOT stand with head or arms over grill. WARNING This procedure MUST be performed OUTDOORS only! Be sure L.P. cylinder valve is closed. Attach to Grill. Read and follow directions on the cylinder and fuel hose safety tags. CAUTION In the connection process, the grill side of the connection will seal on the back-check in the valve, resulting in a slight resistance. The connection requires about one-half to three-quarters additional turn to complete the connection. To disconnect, turn counterclockwise. Tighten by hand only. DO NOT use tools. Step 1 ¦ Make sure Burner Valves are in OFF position. NOTE: Follow this Lighting Procedure to light Burners on one side of the grill then repeat to light the Burners on the other side of the grill. Step 2 ¦ Turn on fuel supply on righthand L.P. gas cylinder. 9 Lighting the Grill continued Step 3 ¦ Turn Righthand Burner Valve to “High.” ¦ Press Igniter Button to light. NOTE: If the flame doesn’t immediately light, turn off control knob and wait five minutes for gas to clear. ¦ Repeat steps 1 through 3. ¦ If the burner does not light on second try, turn off knob and try match-lighting the burner. ¦ Repeat steps 2 and 3 for Lefthand L.P. gas cylinder and Lefthand Burner. NOTE: You must push Igniter Button to ignite the second side of the grill. ¦ All Burner Valves can be adjusted from “Low” to “High.” Match Lighting ¦ Use a LONG wooden match or the match extension provided. Make sure all burner controls are off except one being lighted. ¦ Insert a match in the holder end of the extension, strike the match and place the match near the burner from above. ¦ Turn on BURNER CONTROL KNOB while holding match near burner. ¦ You must use another match to ignite the second side of the grill. Tear Down/Clean Step 1 ¦ Make sure Burner Valves are in OFF position. ¦ Allow unit to cool completely. Step 2 ¦ Turn off fuel supply on both L.P. gas cylinders. 10 Tear Down/Clean continued Step 3 ¦ Remove Regulators from Propane Cylinder Connection. Step 4 ¦ Remove Grease Pans. Slide out from front of grill to clean or install new aluminum liners in Grease Pans. Step 5 ¦ Unlock tab as shown. ¦ Slide out Grease Tray. ¦ Clean thoroughly before storing grill. ¦ Slide Grease Tray back into position under grill and lock tab. Tear Down/Clean continued Tear Down/Clean continued Step 6 ¦ Center Lid goes on first. Step 10 Step 11 Step 7 ¦ Lift up on Right Side Shelf to remove from grill and fold in flaps as shown. ¦ Remove Leg Brace. LEG BRACE Step 8 ¦ Place folded up Right Lid (Shelf) on grill. IMPORTANT: Make sure Lid fits into Channel on Center Lid. ¦ Repeat to store Left Lid (Shelf). ¦ Be sure to replace all three lids after use. CAUTION Because of its size and weight, it is recommended that there are at least two (2) people available to raise legs to the storage pos...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category