Votes - 3, Average rating: 4
(
)
)
|
manual abstract
(FIG. 5B) Hold spacers between leg and body and insert M6 x 90 bolt through leg, spacer, and slotted hole in Grill body. Attach M6 Wingnut, but do not tighten. Repeat assembly for three remaining legs. • With the help of a second person, lift the Grill into the upright position. Grill body should slide down into slotted holes and seat itself. If not, loosen the wingnuts and push down on the corners of the body. • Tighten all bolts and wingnuts. Also tighten all Bottom Shelf and Side Table bolts. Rotate the Lock lever on the Caster wheels to lock or unlock as desired. (15) Grill Body (17) Screw, M6x90mm 8 pc 1 pc (19) Wingnut, M6 (18) Spacer 8 pc 8 pc (16) Bottom Body Panel1 pc FIG. 5B FIG. 5A (19) Wingnut, M6 (18) Spacer (17) Screw, M6x90mm 7 Step 6) Install Control Knobs, Fabric Panel, and Hood Handle: • Align the flat keyed hole in the Control Knobs with the keyed stem of the Control valves. Push the Control Knobs onto the Valve stem. (FIG. 6A) • Open the Hood and position the handle with the bolt heads facing up. Align the threaded holes in the handle with the two holes in the hood. Secure using two M6 x 10 Bolts and two M6 Washers. ( FIG. 6B) • Attach the Fabric Panel by aligning it with the curved edge of the Lower Shelf and pressing it against the velcro patches on each side of the front legs. (FIG. 6C) (20) Control Knob4 pc (21) Fabric Panel1 pc (22) Handle1 pc (24) Washer, M6 2 pc (23) Bolt, M6 x 10mm 2 pc FIG. 6C FIG. 6A FIG. 6B Velcro Patches (23) M6 x 10mm Bolt Valve Stem Handle bolt heads facing up(20) Control Knob (24) M6 Washer 8 To reduce the risk of a cut injury: · Wear protective gloves when handling parts that have sharp edges. Step 7) Install Bottom Panel and Grease Tray: Slide the Bottom Panel into the track at the bottom of the grill body. (FIG. 7A) Secure Bottom Panel into Body Assembly with a ST 4.0 x 10 Screw on each side. (FIG. 7B) Insert the Foil Pan into the Grease Tray and slide the Grease Tray into the guides of the Bottom Panel all the way. (FIG. 7C) (16) Bottom Panel 1 pc (25) Screw, ST4.0 x 10 2 pc (26) Foil Drip Pan (27) Grease Tray 1 pc 1 pc FIG. 7A FIG. 7B FIG. 7C (27) Grease Tray Bottom Panel Guides (16) Bottom Panel Track for Bottom Panel Note: Grill omitted for clarity. (25) Screw, ST4.0 x 10 9 Step 8) Install Flame Diffuser: Place a Flame Diffuser in the guides over each Burner. (FIG. 8) (28) Flame Diffuser FIG. 8 Flame Diffuser Guides Step 9) Install Cooking Grids: Place Cooking Grids onto the front and back Bowl ridges over the Flame Diffusers and Main Burners. (FIG. 9) (29) Cooking Grid (29) Cooking Grid FIG. 9 10 To reduce the risk of serious bodily injury or death: · Use only propane gas in this LP gas grill. · Do not attempt to convert an LP unit to natural gas. · Any use or alteration of this unit not intended could be unsafe and will void your warranty. · Always use a gas appliance outdoors in an open area with good ventilation to avoid breathing toxic fumes from leaking gas, explosion or fire. As with all conventional fuels, the burning process consumes oxygen and produces toxic gases, including carbon monoxide. In addition, the combustion products of such fuels, including liquefied petroleum (LP), contain chemicals known to the state of California and other authorities to cause cancer, birth defects and other reproductive harm. USING GAS CARBON MONOXIDE HAZARD · This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. · Never use this appliance indoors, on recreational vehicles, or boats. CONNECTING/DISCONNECTING THE GAS LP GAS CYLINDER · Never fill the LP gas cylinder more than 80% of cylinder volume. (20 lb. maximum) Do not ask the propane supplier to over-fill the cylinder. · If you obtain LP gas through a cylinder exchange dealer, make sure you get a safe and adequate O.P.D. cylinder. (See page 23) Use only a licensed LP gas cylinder dealer. · Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane. CONNECTING/DISCONNECTING THE GAS LP GAS CYLINDER · Never fill the LP gas cylinder more than 80% of cylinder volume. (20 lb. maximum) Do not ask the propane supplier to over-fill the cylinder. · If you obtain LP gas through a cylinder exchange dealer, make sure you get a safe and adequate O.P.D. cylinder. (See page 23) Use only a licensed LP gas cylinder dealer. · Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane. To reduce the risk of serious bodily injury, fire or death: · Read and follow all warnings on LP gas cylinder. · If you see, smell, or hear the hiss of LP gas escaping from the cylinder: 1. Do not attempt to light appliance. 2. ...