Votes - 3, Average rating: 3.3
(
)
)
|
manual abstract
• Distance in mi or km. For complete Function Specifications, go to page 24. 3 Key Features • Built around the Japanese-made JW200 PedometerEngine™ Step Sensor, the current gold standard for accuracy. • Extra Large Digits. • The ACCUSPLIT exclusive case makes this the slimmest available pedometer built around the JW200 Step Sensor. • Chromed, Spring Steel clip resists breakage. • Case includes two leash slots, for attaching safety leash on either side. Made from tough polycarbonate plastic. • Step filter, can be set from 0-5 steps to further increase accuracy. HOW TO OPEN YOUR PEDOMETER See diagrams at right. The cover must be closed for the pedometer to work. ACCUSPLIT EAGLE DigiwalkerXL.comSTEP TIME DIST CAL SET4728 MODE RESET S3– S1,S2,S4 S3+ 140SXL USE IT NOW! Your pedometer is preset with standardized settings that allow you to use it now!You can customize the settings later. Skip to pages 13-16 to use it now! SETTING UPYOUR PEDOMETER It’s a good idea to set up your pedometer before first using it. To record your distance accurately, you will need to set your stride length. See page 9 when you are ready to set up your unit. 4 5 6 Getting Acquainted • Press the MODE button to cycle through the display modes (Steps and distance.) See page 16 and Specifications for details. • The RESET button sets your counts back to zero. See page 17 for details. MODES • STEP: STEP mode shows step count. • DIST: DISTANCE mode shows distance traveled (mi/km). STEP DIST SET DIGI-WALKERXL.COM 140 XL S3S3+ S1,S2,S4JW200 Mode indicator RESET Button (yellow) 7 Steps Counted MODE Button To avoid losing or dropping your pedometer, use the included leash and clip to fasten the pedometer securely to your First, loop leash through slot on side of pedometer clothing. Attaching the Leash Next, clasp clothing 1. Attach the pedometer to the leash by looping the thin side of the leash through one of the leash slots on the sides of the pedometer case, near the bottom of the unit. 2. Put the pedometer onto your clothing as discussed above. 3. Attach the alligator clip to a belt loop or the top edge of the pants or skirt. Note: You can also use a safety pin to fasten the leash to your clothing, loop the leash through your belt or belt Or, loop a belt or belt loop Or, loop a badge holder, then put into pocket 14 loop, or use a badge holder. 15 (Badge holder not included) 12 Exiting Set Mode Press and hold the S4 button for 2 seconds.The unit will exit setting mode – no values will be flashing anymore. Note:The unit will save any changes and exit set mode after 30 seconds unattended. 13 WEARING YOUR PEDOMETER Gently slide the pedometer onto your belt or the top edge of your pants or skirt. It should fit snugly and level, above one knee.The strong steel clip makes it easy. Note:The pedometer should be as vertical as possible. Walkers with larger stomachs may find it helpful to wear the pedometer farther back on the body, toward one hip. The cover must be closed for the pedometer to work. yes no 10 “in” indicator for inches STEP DIST SET DIGI-WALKERXL.COM 140 XL S3S3+ S1,S2,S4JW200 in Setting Stride Length Stride Length Flashes 11 Finding Your Stride Length: Your stride length is the length of one of your steps, measured from “toe to toe.”To measure, walk 10 steps with your normal stride and measure theTOTAL DISTANCE from the toe of your starting step to the toe of your 10th step (see diagram below). Divide the TOTAL DISTANCE by 10, and multiply the decimal portion by 12 to find your stride length in feet and inches. Example:You walk 23 feet and 6. inches in 10 steps. Convert to feet only = 23.542 feet (6. . 12 = 0.542). Divide by ten to get the stride length in feet = 2.354 feet. Now, convert back to feet and inches to get your stride length = 2 feet 4.25 inches (0.354 . 12 = 4.25). 10 steps 8 SETTING PROCEDURE ACCUSPLIT products use a common setting procedure known as “S1-S2-S3-S4.” Here’s how it works: Press S1 for 2 seconds: Enter the SET mode Press S2: Change the field to be set Press S3: Change the field value Press S4 for 2 seconds: Exit the SET mode You can enter and exit Set mode from any of the regular display screens. 9 Entering set mode Press and hold the S1 (MEMORY) button for 2 seconds. The display will start to flash, showing that you’ve entered SET mode. Setting Stride Length 1. You will see the mode indicator bar underneath DIST and the “in” indicator come on. The display will show a flashing number, which is your Stride Length set point (in inches). 2. Press the S3 + (MODE) button to increase the Stride Length (in increments of . inch), and press the S3( RESET) button to decrease the Stride Length. Hold the buttons down to change values quickly. 22 REPLACING THE BATTERY AND MASTER RESET When the display starts to dim or goes blank, it is time to replace the battery. If the display is not uniformly dim or blank, and appears to display “erroneous data”, do a Master Reset by pressing all 3 buttons simultaneously for 3 seconds an...