Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
. . ... .. This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment. DO read this handbook carefully and keep it handy for ready reference. DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Check that the mains fuse rating is correct. DO always call in your dealer if you are ever in doubt about the installation, operation or safety of your equipment, he is the best person to advise you. DO unplug the power cord if the appliance is left unused. DON'T obstruct the necessary all round ventilation: moderate heat is generated when product is operating - ensure installation is clear of curtains etc. Do not obstruct cooling vents on rear of cabinet. DON'T obstruct the necessary all round ventilation: especially DON'T stand the set close to curtains or on soft furnishing such as carpet. Overheating can cause unnecessary damage and shorten the life of the set. Remember that to obtain the best performance and lasting satisfaction from your equipment : have it regularly maintained by a reliable service organisation: ensure that it is correctly used by all the family. ABOVE ALL: Never let children push anything into holes or slots in the cabinet - this could result in an electric shock. Never guess or take chances with electrical equipment of any kind - it is better to be safe than sorry. WARNING: To prevent fire or shock hazard do not expose this appliance to rain or moisture. No user serviceable parts inside. Refer servicing to qualified service personnel. Never remove covers unless qualified to do so; this unit contains dangerous voltages. LOCATION: LOCATE appliance in the room where direct light does not strike the screen. ALLOW adequate space between the appliance and the wall to permit proper ventilation. AVOID excessive warm and dusty location to prevent possible damage to the cabinet and component failure. NEVER install the appliance in a strong magnetic field. CONNECT the appliance to AC 240 Volts, 50Hz MAINS (AC) OPERATION The wires in this mains lead are coloured in accordance with the following code. Blue: Neutral, Brown: Live 1 PHASE NEUTRAL (LIVE) PRESET DOOR POWER SWITCH SPEAKER REMOTE SENSOR LEDINDICATOR AUDIO IN VIDEO IN ANTENNA PRESET DOOR POWER SWITCH SPEAKER REMOTE SENSOR LEDINDICATOR AUDIO IN VIDEO IN ANTENNA INSIDE THE PRESET DOOR SKIP -MT + PRESET AUTO -VOL + -CH + STAND BY CHANNEL SELECTOR PREVIOUS CALL SLEEP PICTURE/TIME MUTE TV/AV CHANNEL SELECTOR VOLUME CONTROL TIME PICTURE TIMER 2 INSTALLING BATTERIES: 1. Remove the battery cover of Remote Control Unit. 2. Insert two "AA" 1.5V batteries making sure the polarity (+ or -) of the batteries matches the polarity marks inside the unit. 3. Close the battery cover. * When the Remote Control Unit is not used for a long time or the batteries are worn out, take out the batteries to prevent electrolyte leakage. * Take care not to drop, dampen, disassemble the Remote Control Unit. * Operatable remote control range is limited as shown. OPERATING INSTRUCTIONS: ANTENNA CONNECTIONS . Optimum colour reception requires a good antenna. An out-door antenna will be more effective to obtain a clear-picture. . Insert the out-door antenna into the antenna socket on the cabinet back. Adjust the direction or position for the best possible picture. POWER SWITCH . Press POWER SWITCH, the appliance will be in operation mode. The channel position number is displayed in the upper right corner of the screen for 4 seconds. . Press POWER SWITCH again to turn off the appliance’s power CHANNEL SELECTION . Press CHANNEL SELECTOR ( ) on the appliance or the Remote Control Unit, the channel number will be increased or decreased as shown in the following Fig, and display in the upper right corner of the screen. CHANNEL DECREASECHANNEL INCREASE CH 1 2 58 59 CH 8 1 2 58 59 (REMOTE) (THE APPLIANCE) 3 . Use the CHANNEL SELECTOR button on the Remote Control Unit to select channel 1) 0-9 channel 6 6 2) 10-19 channel 1 1 2 12 3) 20-29 channel 2 2 8 28 4) 30-39 channel 3 3 5 35 5) 40-49 channel 4 4 8 48 6) 50-59 channel 5 5 9 59 4 NOTE: To select two digit channel, the second digit must be pressed within 2 seconds. * PREVIOUS BUTTON (REMOTE CONTROL UNIT) Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous program you watched is on channel 15; then you can press the button to reach channel 15, press it again to return channel 6. 6 15 CHANNEL PRESET . AUTO PRESET 1. Press the PSET (PRESET ON/OFF) button on the front panel. The current band and channel position will...