Votes - 0, Average rating: 5
(
)
)
|
manual abstract
(914 mm) C C Cooktop 1 1/2" (38 mm) Typical counter top 3/4” Min.* 36" Typ. (914 mm) A B Warming Drawer (19 mm) C 120 Vac electrical receptacle 27"/30"/36" Dacor single oven D Warming Drawer 120 Vac Elect. Warming Drawer 120 Vac Elect. D Toe Kick 5/8" Min.* A (16 mm) Model “A” Cutout Width “B” Min. Width to Adjacent Doors/ Drawers “C” Cutout Height “D” Min. Vertical Gap Between Cutouts IWD24 22 1/4” (565 mm) 24 1/4”* (616 mm) 9 1/8” (232 mm) 1 1/16”* (27 mm) EWD24 EWD27 25 1/4” (641 mm) 27 1/4”* (692 mm) IWD27 MWDH27 MWDV27 MRWD27 PWD27 EWD30 28 1/4” (717 mm) 30 1/4”* (768 mm) IWD30 MWDH30 MWDV30 MRWD30 PWD30 EWD36 34 1/4” (870 mm) 36 1/4” (921 mm) * Bare minimum spacing shown to allow for ventilation and avoid scrapping. On IWD series models, additional space may be required if an oversized drawer front is used. Use the drawer face dimensions for the corresponding EWD series model on page 4 for reference. Cutouts Dimensions Cutout Depth: 24” Min. (610 mm) Installation Specifications Installation Specifications Install a Support Platform in the Cabinet Provide a platform (100 lb. load capacity) within the cabinet upon which the warming drawer will be supported. The platform must be installed level and straight. The top edge of the platform must be flush with the cutout at the front of the cabinet. There are no provisions to level the warming drawer after it has been installed. 3/4” (19 mm) thick plywood is recommended. NOtE: If the drawer is not installed in a level fashion, the drawer may slide open on its own or may not seal tightly, allowing heat to escape and resulting in poor warming drawer performance. SupportplatformChassisface Electrical Power Supply Requirements • The warming drawer is supplied with a power cord terminated by a three-prong plug. Plug it directly into a dedicated, grounded, three prong, electrical outlet. Do not use an extension cord. Three-Prong Three-Prong Plug Grounded Outlet • The correct voltage, frequency and amperage must be supplied to the electrical outlet from a grounded, single phase circuit that is protected by a properly sized circuit breaker or time-delay fuse. • The required voltage, frequency and amperage ratings are listed on the appliance data plate. The data plate is located inside the chassis drawer opening on the left side. Remove the drawer to expose it. Nominal Electrical Supply Requirements 120 Vac, 60 Hz, 15 Amp. dedicated circuit The warming drawer is supplied with a 40” (1016 mm) power cord with a three prong grounded plug. total Connected Load 0.5 kW (4 Amp.) • If the power supply requirements shown above do not agree with those listed on the product data plate, use the requirements on the product data plate. • It is the owner’s responsibility to ensure that the electrical outlet is installed by a qualified electrician. The electrical installation must comply with the latest revision of the National Electric Code ANSI/NFPA 70 and local codes and ordinances. • If the electrical service provided ...
Other models in this manual:Other Kitchen Appliances - EWD24 (418.87 kb)
Other Kitchen Appliances - EWD30 (418.87 kb)
Other Kitchen Appliances - EWD27 (418.87 kb)
Other Kitchen Appliances - EWD36 (418.87 kb)