Votes - 2, Average rating: 3.5 ( )

Manafacture: Danby File size: 1.23 mb File name: Language of manual:

Water can't pour out from = Hole in the float supply is Suck with dust cleaner or other float support when pull jammed,, let water pour out out the rubber cap. Dishwasher heat runs but not .heater ,Timer element contacts (open). (open or burnt). Replace Replace heater element, timer, =Wiring or t_rminal (burnt or R_p_lr orreplac_ broken). = Thermostat is closed. R_lace. Dishwasher will not stop, ,Timer motor (inoperative). Replace timer =Wiring or terminal (burnt or Repair or replace broken). ,Timem_oe_ burnt contactl:____ Replace timer. Dishwasher runs with ,,Defective door safety switch., Replace door safety switch.. _en Motor hums but will not • Start winding(open),, Replace motor. start or run,. • Motor (bad bearings or locked Replace motor. rotor). ........... Motor trips out on in =Start relay not dropping ouL Replace start relay terminal thermal overload nlmproper vottage, Gheck voltage, pro{ector =Seal faces binding, Repair or replace, •Motor shah blnding. Repair or replace. =Motor windings shorted Repair motor. Ctean and clear area. Library Imaging System Repeated dishwash_cycles Timer does not advance automatically Dishwa"sher wii'i not fili with water, Incomplete water fill Too much water fill D'IshwasheI" Will not pum'p out Water siphons out.. Water leaks. Poor w_sh ability •Timer (contact's o_p'en or burnt) =Motor (inoperative, check resistances): ......... .Timer motor (stalled or open). .Check timer for power to timer motor. =Timer shaft bindinl] or knob interference to escutcheon. •Water supply turns off • Defective inlet valve, -Check valve screen for obstructions .Defective float switch =Timercontact_(openor burnt), ,Wtrin 9 (broken or burnt_, • Low water pressure • Clogged water inlet valve screen, =Timer advanced past sta_ of fill cynic, -Heavy water supply usage elsewhere in home, • Kinked or restricted fllf hose, water inlet valve to till tunnel =Water inlet fill valve defective =Timer contacts (open or burnt) =FI0at arm binding or out of adjustment =Possibility customeduser turned timer past drain cycle. ,Drain pump is restricted • Damaged impeller.. =Wiring or terminal (contacts 0_0_pen orburntL, .Drain hose loop to low. =Drain line connected to a tioor drain not vented. .Spray arm not rotating or split O Overcharge of water ,Tub seal (torn, worn or loose) =Dishwasher door not sealing properly. aDishwasher is not level • Overburden (wrong type of detergent). ahoy, clamp_ _oose_ • Heater element mounting nuts loose =Water seal leaking. • ,.ring is not in position. • Motor and pump assembly not seated proper in tub liner bottom. ,: ,,J _Spray arm not rotating. • improper loading of dishes, pans and other_. -Detergent dispenser inoperative m_nsuff_cient amount of detergent Or the detergent Is old =Damaged or the Impeller I_ broken. • Detergent not dissolve Replace timer Replace timer Replace timer Replace timer Repair or adjust Turn water supply on. Replace inlet valve_ Disassemble and clean screen. Replace switch_ Replace timer, Repair or replac e . Minimum water pressure of 15P.S 1 Clean water inlet valve screen Instruct customer/user to turn tfmer dial to start indicator m_r_, Use dishwasher when water usage is at a minimum. Correct as needed Replace water inlet fill valve Replace timer. Repair,adjustor replace. Instruct customertuser Clear restrictions Replace drain pump, Replace timer Move to proper hetght.. Install vent air gap at counter Check for proper rotation or replace spray arm Check and correct for proper fill Replace tub seal.. Adjust door latch assembly andlor strike.. Level dishwasher properly Instructs customer/user. _')ghten aii clamps secure_. Tighten the nut Use a new water sear, Adjust the ring or replace a new. Replace seat. Clleck for proper rotation instructs customeduser on proper loading per owner's guide.. Repair or replace dispenser On proper amount of fresh deter gent to use Replace pump a_embly. incoming water temperature of t40"F is required to proper dissolve detergent, LibrarySystem Imaging • Improper loadlng of dish'esi-lOO"_" Instruct customerluser on and other,, proper loading per owner' s ,,Heating element (open), guide • incoming water temperature too Replace heating element low, Incoming water temperature of • Wiring or terminal (broken or t40°F for best drying results. burnt) .... I Replace or repair. ..... tergentcupwi, not • Cup binding. Repair or replace. open. • Roll pin retainer or shaft broken. Replace pin, retainer or shaft =Defective bi-metal. Repair or replace ,Timer contact (open or broken). Replace timer. Door will not lath. Door latch damaged. .. Replace door latch. : Rinse agent liquid will not =Electromagnetic valve defectlve, Replace valve. eject, ,Rinse agent dispenser not Mount securely to rear of inner mounted correctly. door panel =Plunger stuck or held in closed Free plunger or adjust plunger release. position. Rinse agent liquid leaks.. ,Container cracker or broken Replace container =Defective seal on plunger. Replace plunger...

Download now

Please, enter two numbers from picture: