Votes - 3, Average rating: 4
(
)
)
|
manual abstract
• The charger is not intended for any use other than charging the exact type of rechargeable battery pack as supplied with the charger. Any other use may result in the risk of fire, electric shock or electrocution. • The charger and battery packs supplied with it are specifically designed to work together. Do not attempt to charge the battery pack with any other charger than the one supplied. • Do not place any object on top of the charger as it could cause overheating. Do not place the charger near any heat source. • Do not pull on the lead of the charger to disconnect it from the power source. • Make sure that the charger cable is positioned where it will not be stepped on, tripped over or otherwise subjected to damage or stress. • Do not use an extension cord unless it is absolutely necessary. The use of an improper extension cord could cause the risk of fire, electric shock or electrocution. • Do not use the charger if it has been subjected to a heavy knock, dropped or otherwise damaged in any way. Take the charger to an authorised service centre for a check or repair. • Do not disassemble the charger. Take it to an authorised service centre when service or repair is required. Incorrect re-assembly may result in the risk of fire, electric shock or electrocution. • To reduce the risk of an electric shock, unplug the charger from the power supply before attempting to clean it. Removing the battery alone does not reduce the risk. • Never attempt to connect two chargers together. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 104°F (40°C) such as alongside sheds or metal structures in the summer. • The charger is designed for use from a standard household electrical supply (230–240 volts). Do not attempt to connect the charger to a supply with a different supply. • If you wish to charge a second battery pack, unplug the charger from the mains supply and leave it for at least 15 minutes. After this time you can charge a second battery pack. Additional safety instructions for the battery pack • The battery pack for this tool has been shipped in a low charge condition. You should charge the battery pack fully before use. • To ensure the longest battery life and best battery performance, always charge the battery when the air temperature is between 18–24°C. Do not charge the battery pack when the temperature is below 4°C, or above 40°C. This is important. Failure to observe this safety rule could cause serious damage to the battery pack. • Do not incinerate the battery pack even if it is seriously damaged or can no longer hold a charge. The battery pack can explode in a fire. • Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks open or cracks, immediately discontinue its use and do not recharge it. • The battery pack utilizes nickel-cadmium cells. Cadmium is considered to be a toxic material. Use an environmentally safe disposal unit at a municipal waste disposal centre to dispose of a damaged or worn out battery. Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Accessories The GMC DEC002SD comprises the following components: 1 Instruction manual 1 Battery charger 1 Magnetic bit holder 2 Interchangeable screwdriver bits Fitting and removing bits NOTE. The drill bit supplied with the DEC002SD is not designed for use with the magnetic bit holder. 1. To use the short drill bit supplied, insert the bit directly into the chuck (1) as far as possible. The drill is now ready to be used. 2. To use the magnetic bit holder, push the bit into the chuck (1) as far as possible. The magnetic bit holder is compatible for use with most standard sized drill bits. Forward/Reverse switch NOTE. This switch allows the direction of rotation of the chuck to be changed: forward for driving, and reverse for removing screws and nuts. 1. Press the top of the forward/reverse switch (2) for driving and press the bottom of the forward/reverse switch to engage the reverse direction. Adjusting the handle The handle can be turned to one of two positions to suit the task at hand. The tool can be used as a straight handled screwdriver or as a pistol grip screwdriver. 1. To change the position of the handle, push the handle adjusting switch (3) forward and twist the handle to the desired position. 2. Release the switch (3) to lock the handle in the new position. Recharging the screwdriver Your screwdriver is supplied to you partially charged and must be fully charged before use. For the first charge, we recommend charging for 10 to 12 hours. 1. Connect the charger plug to the charging socket (4). 2. Connect the mains plug of the charger to a suitable power point. 3. The indicator light...