Login:
Votes - 2, Average rating: 4 ( )

User manual Crate Amplifiers, model TransChorus 210

Manafacture: Crate Amplifiers
File size: 2.11 mb
File name: 3c35eaf7-c190-400a-ba12-34d3f5f5993b.pdf
Language of manual:enesfrde
Free link for this manual available at the bottom of the page



manual abstract


The Power LED (20) will illuminate when the amp is on. Stereo Headphone (22) This 1/4O stereo output jack is designed to accommodate standard, stereo headphones. Plugging a set of headphones into this jack will disconnect the signal going to the power amplifiers of the unit, and no output can be heard from the unitOs speakers. This feature provides an excellent practice tool. Power Amp In (23) These left and right mono 1/4" jacks provide an input to each of the power amplifiers. When used in conjunction with the Preamp Out jacks (24), a stereo effects loop is formed allowing the use of stereo delays and various effects. Preamp Out (24) These left and right mono 1/4" jacks provide an output from each of the preamps. When used in conjunction with the Power Amp In jacks (23), a stereo effects loop is formed allowing the use of stereo delays and various effects. Remote Switch (25) This jack is provided for the connection of the supplied footswitch. The footswitch is a multi-function type allowing you to select Clean, Crunch, or Lead and to defeat the Chorus effects. To use the footswitch ensure that the footswitch plug is inserted fully into the jack and that the Select switch is pressed in (down position) on the front panel. 6 21 26 22 23 24 23 24 25 AC LINE CORDN120 V PRODUCTS ONLY (26) For you safety, we have incorporated a three-wire line (mains) cable with proper grounding facilities. It is not advisable to remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding facilities, suitable grounding adapters should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles. NOTE: FOR UK ONLY As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in your plug, proceed as follows: • The wire which is colored green and yellow must be connected to the terminal which is marked by the letter E, or by the earth symbol, or colored green or green and yellow. • The wire which is colored blue must be connected to the terminal which is marked with the letter N, or the color black. • The wire which is colored brown must be connected to the terminal which is marked with the letter L, or the color red. 7 8 RECOMMENDED SETTINGS: In In In In Out CLEAN METAL MODERATE DISTORTION In To Taste Out In Out In Out CLEAN BLUES To Taste In In Out In To Taste RHYTHM BLUES LEAD BLUES JAZZ CLEAN JAZZ RHYTHM JAZZ LEAD To Taste To Taste Out In Out TRANSCHORUS. 210 SPECIFICATIONS (ALL MEASUREMENTS @ 120 V AC, 60HZ) POWER AMPLIFIER SECTION RATED OUTPUT POWER: Power specs measured with T. Dynamics @ 100% (5% THD, 1 kHz, 120 V AC) 50 W RMS per channel, into 8 ohms FREQUENCY RESPONSE: Stereo mode into 8 ohm, power amp inputs -3 dB, +2 dB, 70 Hz to 20 kHz, @ 45 W RMS into 8 ohms HUM AND NOISE: Unweighted, 20 Hz to 22 kHz Greater than 90 dB, both channels POWER CONSUMPTION: Domestic Model: 120 V AC, 60 Hz, 2.5A, 300 W Export Model: 220 to 240 V AC, 50/60 Hz, 300 W PREAMP SECTION (The following specs are measured @ 1 kHz with the controls preset as follows:) Push Bright, off (out) Channel Select Clean (out) Low and High @ 10 Mid @ 0 Crunch Pre and Post Gain @ 10 Gain and Thrash, off (out) Lead Pre and Post Gain @ 10 Gain and Mid Boost, off (out) Normal levels are with normal volume @ 5 Minimum levels are with clean volume @ 10 PREAMP HIGH GAIN INPUT: Impedance: High-Z, 1 M ohm Nominal Input Level: -12 dBV, 250 mV RMS Minimum Input Level: -22 dBV, 79 mV RMS Maximum Input level: 0 dBV, 1 V RMS PREAMP LOW GAIN INPUT: Impedance: High-Z, 44 k ohms Nominal Input Level: -6 dBV, 500 mV RMS Minimum Input Level: -16 dBV, 158 mV RMS Maximum Input level: 6 dBV, 2 V RMS PREAMP OUTPUT: Load Impedance: 300 ohm or greater Nominal Output Level: 0 dBV, 1 V RMS POWER AMP INPUT: Impedance: High-Z, 30 k ohms Designed Input Level: 0 dBV, 1 V RMS (Switching jack provides preamp output to power amp input connection when not used.) SYSTEM HUM AND NOISE @ NOMINAL INPUT LEVEL UNWEIGHTED, 20 Hz to 22 kHz Greater than 75 dB, below rated power EQUALIZATION: Special low, mid and high passive type EQ Push Bright: +4 dBV @ 2 kHz, (Clean channel) Push Thrash: -6 dBV notch 1 kHz, (Crunch channel) Push Mid boost: +3 dBV band pass 1 kHz, (Lead channel) Push Gain: Increase gain both Lead and Crunch channels EXTERNAL FOOT SWITCH FUNCTIONS: Lead/Crunch: Selects lead or crunch channel. Bypass/Clean: Lead and Crunch channel defeat (channel switch OINO) Select/Chorus: Defeat Chorus DIMENSIONS AND WEIGHT (H x W x D): 18.5" x 23.375" x 11.375" 47cm x 10.60cm x 29cm 9 10 TransChorus . 210 BLOCK DIAGRAM TONE CLEAN HIMIDLO STEREOCHORUS DEPTHRATE EQUALIZATIONHIGHMIDLOW VOLUMECLEAN PUSHMIDBOOST HIGHGAIN AMP LEADSWITCHLOGIC SWITCH LOGICCLEAN/ULTRA INPUTS 1stGAIN STAGE LEADPOST PUSHBRIGHT PUSHBRIGHT PREGAINLEAD LEADFOOTSWITCH FOOTSWITCH PUSHCHANNEL CRUNCHPREGAIN PREGAIN PUSHTHRASH POSTCRUNCH REVERB SPEAKERPR...

Other models in this manual:
Musical Instruments - TransChorus 210 (2.11 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category